Shopping from Canada? 
Go to Defender Canada!
Trident
Trident Marine 202V Series Silicone Soft Wall Wet Exhaust and Water Coolant Hose
Item: #886306 | Part Number: Not Selected$36.99 - $409.99
Description
- High-temp silicone construction for wet exhaust and coolant systems
- Extra thick, soft wall design with polyester reinforcement
- Handles up to 350°F while reducing engine room heat
- Meets or exceeds SAE, ABYC, and NMMA marine standards
- Backed by a 10-year warranty for long-term reliability
Trident Marine 202V Series Silicone Soft Wall Wet Exhaust and Water Coolant Hose Item # 886306
Description
Trident 202V Silicone Marine Wet Exhaust and Water Coolant Hose provides the kind of performance expected by operators of special service vessels and super yachts. Silicone naturally handles higher temperatures and will last longer than rubber exhaust hose. Silicone will also transfer less heat into the engine room. The 202V series hose is designed for short, straight connections and comes with a 10-year warranty.
Features:
- Extra thick, soft wall, silicone construction
- Very high temperature performance and extra long service life
- Has 4-6 ply polyester reinforcement
Specifications:
- Material: High Temp Silicone
- Reinforcement: Polyester
- Color: Blue
- Tolerance: 350° F (177° C)
- Exceeds (SAE J2006-R1, and ABYC & NMMA P-1 exhaust standards)
Part Numbers for Trident Marine 202V Series Silicone Soft Wall Wet Exhaust and Water Coolant Hose
Reviews
Rated 5 out of
5
by
Lee322 from
Great product
Worked well, replaced hard rubber exhaust section on Cummins 6bta 370
Date published: 2026-04-30
Rated 4 out of
5
by
Keelhauld from
Silicone vs Wire Reinforced Rubber
Traditional wire reinforced rubber hose did not work for our application. Our situation was a little frustrating; we had to replace the exhaust elbow on our Fischer Panda genset. The installation requires a short segment of hose between the exhaust elbow and an 90 degree fitting (an elbow) where the exhaust exists the case, enclosure, capsule...I forget what Fischer Panda actually calls it.
The frustration came in the fact that the 90 degree fitting required a 1.5 inch internal diameter hose and the 1.5 inch ID hose I had fit perfectly on that fitting. But the nipple on the end of the exhaust elbow above it was too big for 1.5 inch ID hose...I'm sure there was probably a way to press that reinforced hose onto that fitting if you had the right tools but there was absolutely no way I was going to get it on by hand. I actually removed the elbow and tried to push the hose on using all my strength and weight from directly above and still couldn't get it on. And even if I had found a way to force that hose on, given what the old hose looked like I don't think that was a smart way to go...note the split in the hose in the attached photo. Why Panda did this, I have no idea.
A marine diesel mechanic told me HDI Marine makes an after market stainless steel exhaust elbow for this genset that is properly sized and he has also seen people take the OEM part to a machine shop and have it machined to the proper size. My solution was to purchase this hose. While it was expensive compared to traditional wire reinforced rubber hose, is was cheaper and faster than the other two solutions. This hose is far more flexible than its rubber counterpart and I had no issue getting it on the exhaust elbow without the risk that it will split like my old hose did.
Date published: 2025-08-30
Questions
What size clamp For 6” inside diameter silicone exhaust hose
6.5 in for 202V6000.
Date published: 2025-04-11