Shopping from Canada? 
Go to Defender Canada!
Description
- Monitors two tanks with a single compact unit
- Compatible with SCAD external and internal sensors, plus most fuel float sensors
- Continuous read and user-selectable visual alarms for full or empty conditions
- Easy surface-mount installation with low power draw
SCAD TM2 Tank Monitor for Two Tanks - 10041 Item # 880427
Description
Features:
- Monitor two fresh water, grey water, or holding tank levels by simply tapping a touch-pad
- Can be used with a variety of sensors (All sensors sold seperately)
- Optional external sensor easily sticks onto the outside of plastic and composite tanks
- Optional internal sensor available for metal tanks
- Compatible with most fuel float sensors
- Compact surface mount size (only 1/2" hole required for wires)
- Continuous read function provides hands-free monitoring
- Visual alarm that is user selectable on for empty or full
- External alarm control wire
- Accommodates all tank shapes
- Easy to install, easy to operate, reliable and cost effective solution for monitoring tank levels
- Tank level can be continuously viewed while filling or emptying tank
- Powers external devices during alert conditions
- Small surface mount footprint saves space
Specifications :
- Power: 12 to 24V DC
- Size: 2.2 x 2.2 x 0.3 inches (56 x 56 x 7.6 mm)
- Sensor Type (All sensors sold seperately)
- SCAD external sensor available for water and waste
- SCAD internal sensor available for metal tanks
- Monitor is compatible with 240 to 33 Ohm and 10 to 180 Ohm float sensors for fuel
- Alarm: Visual alarm on empty or full, or no alarm
- Power wire provides 1 amp at battery voltage; can be set to energize on alarm condition
Part Numbers for SCAD TM2 Tank Monitor for Two Tanks - 10041
Reviews
Rated 5 out of
5
by
SV Athena Too from
SCAD TM2 Tank Monitor for Two Tanks
After rebuilding our black water system, we went with the standard KUS float switch install in our holding tank. In less than 8 months we had to remove and clean the float twice to get the float moving inside the float tube. We are live aboards, do not put paper into our holding tank, and have our tank pumped once a week. The installation and programming was simple enough. While I prefer the accuracy of the KUS system as opposed to the digital LED scale, it is sufficient for our needs and (for now) no longer have to worry about how close to full our tank is. While we are not using it, the alarm feature is a nice touch.
Date published: 2026-07-14
Rated 4 out of
5
by
Kevin H from
Good product 1 issue
Love it except that the you must calibrate empty and full before you get full usage which is a bit infeasible especially for waste tanks. Run wires and calibrate in a separate bucket or pvc tube of water then drop in your boat tank.
Date published: 2026-02-03
Rated 5 out of
5
by
Anonymous from
Love it
Installed easily works great. 4 hokding tanks two dual monitors
Date published: 2025-11-06
Rated 5 out of
5
by
TomD from
Perfect.
Works perfectly. Just what i needed for my fresh water and holding tanks
Date published: 2025-10-06
Questions
Is this product ignition protected and safe for installation in the engine room of a gas powered boat?
The manual doesn't say one way or the other. Suggest you check with the mfgr, see
scadtech.com
Date published: 2024-03-28
Is a installation manual available?
https://scadtech.com/tmhelp/ Is the website.
Date published: 2023-11-26
Will this work with a dual tank 2 wire set up from KUS? My current gauge is an old Fireboy with 4 wires
I'm not sure what you're asking. I have SCAD with two sensors, one on my water tank and one on the holding tank. I have two water tanks but they are usually connected when not underway so by calibrating E and F when connected I have a good idea of how much water we have.
Date published: 2024-09-25