Item #877630

Poli Glow Restorer - Refill - POLI GLOW

00 Review
Want an email once available?
Image of : Poli Glow Restorer - Refill - POLI GLOW

Poli Glow Restorer - Refill - POLI GLOW

Item # 877630


Poli GlowRestorer gives the protection and glow of a professional wax job without the need for rubbing compounds and wax buffing. The Poli Prep (Sold Separately) Poli Glow process is a proven concept in boat polish and is NOT a wax. It is easily applied using the included mitt without the need for rubbing or buffing. It requires only a soap and water wash of the hull prior to starting, but won't wash off with soap and water once it's applied. A minimum of 4 to 6 coats (each coat should dry in approximately 1 to 2 minutes; minimum temp: 55F) is recommended for the initial project and a quick and easy reapplication of just 2 or 3 coats every 12 months (6 to 8 months in tropical areas) should keep your hull shiny and bright!

Poli Glow has been featured on "Ship Shape TV."


  • Restores, protects finish
  • Container: 32 oz bottle
  • Applies easily without the need for rubbing or buffing
  • Won't wash off with soap and water
  • Application:
    • Minimum of five coats. Each coat will dry in approximately one minute
    • Use two applicators, a small one for hard to reach areas and a large applicator
    • A large applicator can be fastened to any threaded pole for easy application
  • Do not treat Poli Glow like a wax
    • Apply Poli Glow, instead like a paint or varnish
    • It should be applied to the surface gently
    • Do not push down on applicator, this may cause foam or bubbles which may dry rough
    • Do not stop applicator, instead pull away from surface gradually
    • If drips occur, remove them with applicator before they dry
    • Avoid windy conditions.
  • How to Apply Poli Glow.
    • This is the easy part
    • Apply Poli Glow to the applicator and allow a minute to soak into applicator
    • Pick a small 2' x 2' flat surface to see what Poli Glow will do
    • Working in small sections (3-4 foot), lightly wipe Poli Glow onto the surface in thin, even, overlapping strokes
    • Make sure application is dry, approximately on minute at 55° - 95° F, before applying the next coat
    • If you go over Poli Glow before it is dry you will get brush marks
    • Apply a minimum of five coats
    • The first two or three coats may appear dull or streaky due to penetration into the fiberglass
    • Poli Glow may be applied in direct sunlight except with dark colors
    • When overlapping you may see areas that are shinier
    • They will disappear in 24-48 hours
    • Avoid contact with rain for several hours
    • If water spots occur they will disappear after a few hours in the sunlight
  • Maintenance:
    • Poli Glow is a unique product
    • It will not wash off or be affected by soap and water
    • A mild boat soap will keep your boat shiny and clean
    • To maintain a shine for more than twelve months, reapply one or two coats at the beginning and end of each season or every 4 to 6 months
    • To re-apply, clean boat with soap and water and apply Poli Glow
    • If stains are left on the surface and penetrate Poli Glow, use Clenz-All to remove stains
    • Then re-apply Poli Glow
    • If scratches or wear spots occur, they can be touched up by applying a few coats of Poli Glow
    • Maintenance is easy, as dirt and grime will not adhere to Poli Glow finish
    • Avoid contact with ammonia based products, degreasers, teak or hull cleaners and abrasive cleaners

Part Numbers for Poli Glow Restorer - Refill - POLI GLOW




  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 28.84ms
  • bvseo-msg: HTTP status code of 404 was returned;


  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 32.34ms
  • bvseo-msg: HTTP status code of 404 was returned;