Item #870824

Isotherm ITC Digital Display Intelligent Temperature Control - SED00036DA

00 Review
10% off
Want an email once available?
Buy with
Image of : Isotherm ITC Digital Display Intelligent Temperature Control - SED00036DA

Isotherm ITC Digital Display Intelligent Temperature Control - SED00036DA

Item # 870824


The Isotherm ITC Digital Display Intelligent Temperature Control (SED00036DA) clearly displays, controls and regulates the temperature in a refrigerated compartment from the exterior of a fridge/freezer cabinet. This helps keep the keep the cold in and can reduce the amount of power used by the refrigeration unit.

Note: The system must be configured via mechanical switches to match the specifications of the refrigeration cabinet (size, usage as a fridge/freezer). The device is compatible only with control units IWM P/N SEG00002DA Secop version 101N0212 and IWM P/N SEG00030GA Secop version 101N0510. Make sure that your device is equipped with one of the a.m. control units before installation.


  • The Isotherm ITC Digital Display canSED00036DA
  • Reduces on board power consumption
  • Main operating parameters are handled by the micro processor in order to maximize performances
  • Remote product interaction is extremely easy and accurate since data readings appear on the display
    • Temperature set
    • Detected selection of energy saving operations
    • Choice of (3) battery protection levels
    • Compressor's operation mode settings (ITC, Eco and Overcooling mode)
  • Simple kit, quick and easy to install
    • Upgrades Isotherm fridges with Danfoss/ Secop compressors
    • The device is fully compatible with the control unit IWM P/N SEG00002DA (Secop version 101N0212 for BD35/50F), allowing recess flush or wall mounted installation
  • Up to 25% energy savings solely due to compressor efficiency gains
  • Up to 40% energy savings with combined effect of cold energy surplus stored in food / drinks
  • Boost mode for quick cooling
  • The product is equipped with a Soft Start function to avoid starting surges
    • The number of compressor revolutions is kept to the minimum allowed for approximately 30 sec. at every start of the compressor
    • It balances the internal pressures on the gas circuit, preventing possible compressor blocks
    • At the end of this process the compressor's operation returns to the standard settings
  • No need for eutectic plates
  • Includes Over Cooling to accumulate cold when there is a surplus of energy:
    • When battery is in charging mode (battery charger, engine on, etc.)
    • If provided with AC/DC kit when shore power is available
  • Smart storage and use of cold energy
    • Isotherm Smart Energy Control optimizes not only the efficiency of Danfoss/Secop compressor but also uses the cooling energy storage potential of food and drinks inside the fridge
    • A continuous monitoring of the cabinet air temperature through a dedicated air sensor allows an over-cooling while preventing any freezing of the food
    • The cooling energy is stored when a power surplus is available (engine on or connection to the grid) and used when the system runs exclusively on battery.
  • ECO Mode function
    • Normally de-activated, ECO function needs to be put on by the user in order to be started
    • With ECO function active, the refrigerator will operate at minimum power, in energy-saving mode
    • Achievement of the set temperature cannot be guaranteed in this mode since priority is shifted to reduce power consumption and the capacity of the battery is preserved to the maximum achievable timing. When the ECO function is active, the Soft Start function is available and the compressor operates at the fixed RPM value of 2500
  • Continuously optimized compressor efficiency
    • The sophisticated, processor-based Isotherm Smart Energy
    • Control technology achieves significant savings in terms of power consumption by continuously scanning a set of key environmental factors to determine through advanced proprietary algorithms, the optimum compressor speed which maximizes the performance/ battery drain ratio (COP)

In the Box:

  • Instructions manual
  • Digital display
  • Digital display support frame
  • Container for wall installation
  • Container for flush mounting installation
  • Temperature sensor with cable
  • Grille and temperature sensor support
  • Display connection cable
  • Filter and prolonging cable for AC/DC
  • (2) M2.5 Screws
  • (2) Self-tapping screws
  • Rubber cable grommet

Owner's Manual (8.43 MB)

Data Sheet

Digital Display Owner's Manual

Part Numbers for Isotherm ITC Digital Display Intelligent Temperature Control - SED00036DA



Related Categories

Related Categories


  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 39.91ms
  • bvseo-msg: HTTP status code of 404 was returned;


  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 20.37ms
  • bvseo-msg: HTTP status code of 404 was returned;