Item #872478

Lenco Aftermarket Digital Auto Glide Kit with NMEA GPS Antenna - Dual Actuator - 15501-101

00 Review
$1,811.99
Want an email once available?
Buy with

Image of : Lenco Aftermarket Digital Auto Glide Kit with NMEA GPS Antenna - Dual Actuator - 15501-101 Lenco Aftermarket Digital Auto Glide Kit with NMEA GPS Antenna - Dual Actuator - 15501-101 Item # 872478

Description

Features:

  • Boat must have a Lenco Dual Trim Tab System with Lenco Electric Actuators
    • This is a MUST in all applications
  • A Real Automatic Boat Control / Trim Tab Control System that actually works
    • Completely & automatically!
  • The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again
  • The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed
    • This optimum running angle is determined during the set-up process after the installation of your Auto Glide system
  • Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to:
    • Automatically put your boat in the most efficient running angle
    • Reduce the amount of bow rise of your boat during hole shot mode
    • Eliminate bow porpoising (bow bounce)
    • Keep your boat level at all times
  • These actions will result in a smoother ride and the best possible fuel efficiency
  • The Auto Glide Control Box (brain) consists of gyroscopes, accelerometers, and new, very sophisticated, and patented software
  • The Auto Glide has (3) Automatic operational modes, (4) Automatic settings, and (2) Manual operational modes
    • Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the (4) Up/Down Buttons on the key pad
    • All of these functions are fully explained in our Owner's Manual B / Operational Instructions
  • Notes:
    • The Auto Glide does not control the "trim" function of your Engine(s) or Motor(s)
    • Please remember to use the trim feature exactly as you would in the normal operation of your boat

Components of the Auto Glide System:

  • The main components:
    • Auto Glide Key Pad
    • Auto Glide Control Box (Single Actuator and Double Actuator per Trim Tab Versions)
    • Control Box Main Harness (Same 2 versions)
    • Various cables
      • These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver
  • Second Station Kits and a vast array of other accessories and parts which may be required for your installation are also available (Purchased Separately)
  • Lenco offers Aftermarket Kits for easy installation on ALL boats, CANbus-equipped or not
  • OEM applications can be specially kitted to be boat or OEM specific

Applications:

  • Aftermarket Systems:
    • The Lenco Glide System will work on ALL boats with ALL engines
    • GPS data is used to provide data to control box
    • Optional connection to NMEA 2000 Network is included
  • OEM System:
    • Connection to analog systems is available
    • Connection to CANbus-based engines is available. See list below
    • Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver
    • NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket
  • CANbus-based engines:
    • NMEA 2000 Engines
      • Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000)
      • Evinrude
      • Honda
      • Suzuki
      • Volvo Penta (Non-EVC Engines) (With a Volvo NMEA 2000 Gateway - Volvo P/N 3889757)
    • J1939 Engines
      • Volvo Penta (EVC Engines)
      • Yanmar
      • Caterpillar
      • Cummins
      • Detroit Diesel
      • John Deere
      • Stey
    • SmartCraft Engines
      • Mercury - Verado
      • Mercury - Optimax with SmartCraft ECU
      • Mercruiser with SmartCraft ECU
      • Cummins/Mercruiser w/ SmartCraft ECU
  • Installation Notes:
    • The Auto Glide can be connected to your engine's CANbus system, to your boat's GPS system (direct to unit or network) or to a GPS Stand-Alone antenna/receiver
    • Different systems and applications present unique challenges
    • You may want to consider soliciting the help of an installer that possesses experience in CANbus systems, connecting products to GPS networks, etc., and/or NMEA 2000 Network experience
    • Lenco's Aftermarket Kits include a "must install" GPS antenna/receiver and can be installed by most marine mechanics and do-it-yourselfers
    • A Schematic must be printed from internet site (or print from pdf download) and must be followed exactly as shown

Owner's Manual A

Owner's Manual B

WARNING

This product can expose you to chemicals including di(2-ethylhexyl)phthalate (DEHP) which are known to the State of California to cause cancer, birth defects or other reproductive harm.

For more information go to www.p65warnings.ca.gov.

Part Numbers for Lenco Aftermarket Digital Auto Glide Kit with NMEA GPS Antenna - Dual Actuator - 15501-101

Related Categories

Related Categories

Reviews

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 22.11ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Questions

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 38.85ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;