Item #861412

Awlgrip High Build Epoxy Primer - D8002Q

00 Review
$49.99
Want an email once available?
Buy with

Image of : Awlgrip High Build Epoxy Primer - D8002Q Awlgrip High Build Epoxy Primer - D8002Q Item # 861412

Description

Awlgrip D8002 High Build Epoxy Primer is a two component epoxy primer for use where high build and filling is required. This product is not to be used below the waterline.

Features:

  • High build, two-part epoxy primer
  • Use where high build and filling is required
  • Best applied using a paint sprayer
  • Not recommended for roll and tip applications
  • Not to be used below the waterline
  • Best when used over other Awlgrip primers and fairing compounds
  • May be applied directly to properly prepared wood or fiberglass
  • Best results are obtained when these surfaces are first sealed with 545 Primer
  • Best when used over other Awlgrip primers and fairing compounds. May be applied directly to properly prepared wood or fiberglass, however best results are obtained when these surfaces are first sealed with 545 Primer
    • Gelcoat/Fiberglass: Sand with 100-150 grit paper
    • Wood: Smooth sand with 80-100 grit paper

Mixing and Reduction:

  • Mix by volume one part base with one part converter to a smooth homogenous mixture
  • Induction time after mixing: 15 minutes
  • Reduce 10-20% with appropriate reducer
  • Anticipated Pot Life time at 77° F/50 relative humidity is 8 hours
  • Higher temperatures may shorten pot life

Application Instructions

  • Apply Awl-Grip High Build Epoxy Primer in even coats of 8 to 10 mils (200-250 microns) wet film thickness yielding 4 - 5 mils (100 to 125 microns) DFT. Two to three coats may be needed.
  • Do not apply to surfaces warmer than 105 F or colder than 55° F. Do not attempt to cure products at temperatures below 55° F. Do not apply to surfaces less than 3° C or 5° F above Dew Point or to surfaces warmer than 41° C/105° F. Ambient temperatures should be 13° C/55° F - 41° C/105° F

Specifications:

  • Type: Epoxy polyamide
  • Size: 1 quart
  • Theoretical Coverage (sq. ft./Gallon)
    • 814 sq. ft. at one mil dry
    • 113 - 158 sq. ft. at recommended dry film thickness with 2 coats
    • Calculated for mixed base and converter reduced 20%
  • Coverage calculations are based on theoretical transfer efficiency of 100%
  • Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and environment
  • Recommended Wet Film Thickness: 8 - 10 mils (200 - 250 microns)
  • Recommended Dry Film Thickness: 5 - 7 mils (125 - 175 microns)
  • Recoating Times:
    • With itself: 4 hours
    • With other products: 12 - 24 hours
    • Maximum window without sanding: 24 hours
  • Sanding before overcoating with other products is recommended
  • May be overcoated with 545 Epoxy Primer, ULTRA-BUILD, Sprayable Fairing Compound, AWL-FAIR L.W., and AWL-QUIK
  • VOC: White Base D8002 - 347 g/ltr or 2.9 lbs/gal. Yellow Base D9002 - 338 g/lt or 2.8 lbs./gal

Note: This multi-component system is intended for experienced painters. Please read mixing and application instructions thoroughly prior to starting project to ensure best results.

WARNING

This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm.

For more information go to www.p65warnings.ca.gov.

Part Numbers for Awlgrip High Build Epoxy Primer - D8002Q

Related Categories

Related Categories

Reviews

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 3.07ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Questions

  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 3.97ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;